You won't be able to use two steps at the same time, so you will need to remove the current step to install your Glow Step. You can save that step and reinstall on that trailer once you get a newer trailer to put your GlowStep on.
From your picture, it looks like the TorkLift GlowStep Revolution Vertical Stud Adapter Bracket # TLA8022 can be used to install your GlowStep. view full answer...
There is not a 40 inch height top step; the tallest is the 27-1/2 inch tall Econo Porch Trailer Step that comes with either a single or double hand rail:
- Econo Porch Trailer Step with 2 Handrails and Landing # EHS-103-R-HR
- Econo Porch Trailer Step with Handrail and Landing # EHS-103-R view full answer...
Steps such as # AS24 are not designed for permanent installation on a 5th wheel trailer. These steps are meant to be removed/installed when needed and you normally see them on in-bed campers.
The other issue is that if you added permanent mount steps to your 5th wheel trailer the additional step could cause the whole assembly to hang too low and cause ground clearance problems while towing the trailer.
The best solution is a separate step that you can carry with you in the trailer or... view full answer...
To get that third step the best option for you is the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR98RR. This will attach to the floor just past your door frame and fold up into the trailer while not in use. view full answer...
In order to determine a suitable SolidStep Manual Fold-Down RV Step for a Forest River R-Pod Travel Trailer you'll first need to measure the doorway width (inner most point to inner most point) followed by the threshold height (ground to floor of trailer where step mounts). The SolidStep Manual Fold-Down RV Steps part # LC713662 for example are designed for a doorway width up to 24" with a threshold height between 22" and 28".
I have attached our full list of step options below if this... view full answer...
The Econo Porch Trailer Step with Handrail # EHS-102-R is a fixed step setup that doesn't have any moving parts. It sits 21 inches off of the ground at the very top step. As long as you position the step near your trailer so that it doesn't interfere with your electric step it should fit and work well for you.
The handrail dimensions are 25" deep x 37" tall (front) x 44" tall (back). view full answer...
The stored depth of this step from the center of the front mounting hole to the back of the slide bracket measures 11 inches. The height of the step will be 7 inches when it is stored. I have attached diagrams showing these measurements.
To make sure this step will work for you, you will want to make sure that you have at least 11 inches behind the mounting location of the front bolt hole to install this step. As long as you have the 11 inches behind the front bolt hole, this step should... view full answer...
The Econo Porch Trailer Step with Handrail and Landing # EHS-103-R do ship mostly assembled. To set up these steps you will remove them from the box and raise the steps. There are 8 struts that are only bolted on one side of the steps. When you stand up the steps you will bolt the struts up with the 8 nuts and bolts to hold the steps in the upright position. The handle will then be attached with the 2 longer bolts that come with the steps. view full answer...
Is the overall width of the base 26 inches or is that the center to center distance between the mounting holes? Because if it is the mounting hole distance then steps # LC432687 will fit but the overall width is 27-1/2 inches.
The other issue is that when you add additional steps it makes them closer to the ground when stowed. This reduces ground clearance and can result in loss of steps.
An alternative is to use a portable step such as # S-150 that you can keep in the RV/trailer and... view full answer...
I reached out to my contacts at Lippert and they only have stairs without a landing. I reached out to my contact at Stromberg Carlson and they have the landing with two steps in their Econo Porch Trailer Step with Handrail and Landing - Double - 7" Drop/Rise, 20-1/2" Tall, # EHS-102-R, but they do not have a landing with a single step.
Depending on the height of your RV, you may be intereset in the Safety Step Adjustable Height, Folding Platform Step - Aluminum - 24" x 16" - 1,000 lbs,... view full answer...
The only 4-step aluminum steps we carry are scissor steps such as # AS24 but they are not designed for permanent installation on a 5th wheel trailer. For steps that are designed for permanent installation on a 5th wheel trailer you can use Stromberg-Carlson model # SMFP-4400. view full answer...
I recommend the TorkLift GlowStep Revolution Scissor Step # TLA8102 for the biggest improvement in stability and comfort on your Aspen Trail.
This USA-made steel and aluminum 2-step unit is compatible with your mounting brackets and your 26-inch frame-to-ground clearance. Since this step has built-in landing gear legs that stabilize the whole step you'll not send the trailer into motion each time you enter or exit, which can occur with simple pull out steps like # 953240RXWC3. Extra large... view full answer...
The Lippert # LC432682 manual pull out two-step stairs is the closest match. Replacement steps only come in a few sizes. This step is 25-1/2" wide at the widest point. The next sizes are about 18" or 30". Using some washers seems like a good solution. You will likely have to drill new mounting holes to match your 3" on center holes. After that you will have a sturdy step rated for up to 300 pounds.
The perfect compliment to these steps is the Camco # CAM42177 grab handle. I have these... view full answer...
We don't know the threshold height of your Sunny Brook 34 ft 5th wheel but we can tell you that the overall height of the tallest step on the Econo Porch Trailer Step with Handrail # EHS-102-R is 20-1/2 inches. You'd have to compare that to the height of your door to know how big of a step that last one would be. Each of these steps has a drop of 7 inches. view full answer...
You could potentially use TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 5 Steps - 27-7/16" Base - 300 lbs Item # TLA8005 instead of a 4-step model. Choosing a set of these steps is based on the height of the unit once installed. According to TorkLift the optimal mounting height is measured from the ground to the top of the GlowStep Revolution Frame when the trailer is leveled on flat ground. For the 5-step model that height is 42-3/4 inches. The 4-step model # TLA8004 has... view full answer...
You're correct that you need 5th wheel replacement steps to extend down from the mounting point the same distance as the original steps do. This will avoid loss of ground clearance which is an important safety consideration.
Trailer makers typically do not provide detailed specs on components such as steps that are used in their products but you can use the linked page to see our range of 4-step scissor steps. Brophy step # AS24 is 24-inches wide like yours, offers a 7-7/8-inch step height... view full answer...
Currently the only other style of trailer step we offer aside from the # HE4036 that you referenced would be trailer fender steps like part # CE19011 for the left front/right rear or the part # CE19012 for the right front/left rear. view full answer...
I checked with Torklift and was able to confirm that the correct 4-Step Assembly for your 2017 Grand Design Reflection is the GlowStep Revolution Scissor Steps # TLA8004. This will be perfect for replacing the factory 3-step assembly on your trailer. This features 8 inch deep and 22 inch wide aluminum steps that provide 3 different height settings. Glow tape will create a lighted step surface for nighttime applications.
The mounting base itself measures 27-7/16 inches wide and 12 inches... view full answer...
The Tandem Axle Teardrop Trailer Fenders part # HP94VR don't have built-in step at the front or rear that is correct. If you're looking for a step here, I recommend simply adding a frame mounted step like the HitchMate Boat Trailer Step part # HE4036 or CE Smith Galvanized Steel Step part # CE26212G-15284GA. These are both very cost effective options and easy to install. They also won't damage the fender if anything happens either. The best part of all is that you can position them exactly... view full answer...